❏ 站外平台:

Linux 有问必答: 如何在红帽系linux中编译Ixgbe驱动

作者: Dan Nanni 译者: LCTT Vic___

| 2015-06-03 03:33   收藏: 2    

提问:我想要安装最新版的ixgbe 10G网卡驱动。在CentOS, Fedora 或 RHEL中,我应该如何编译ixgbe驱动?

想要在linux使用Intel的PCI Express 10G网卡(例如,82598,82599,x540),需要安装Ixgbe驱动。如今的Linux发行版都会预安装ixgbe的可加载模块,但是预安装的ixgbe驱动不是完整功能版。如果想要开启和定制所有10G网卡的功能(如,RSS、多队列、虚拟化功能、硬件 offload 等),需要从源码编译安装。

本文基于红帽系平台(如,CentOS,RHEL或Fedora)。Debian系平台,请看这篇文章

第一步: 安装依赖

首先,安装必要的开发环境和安装匹配的内核头文件

$ sudo yum install gcc make
$ sudo yum install kernel-devel

第二步: 编译Ixgbe

官方页面下载最新Ixgbe源码

$ wget http://downloads.sourceforge.net/project/e1000/ixgbe%20stable/3.23.2/ixgbe-3.23.2.tar.gz 

请检查支持的内核版本。例如,Ixgbe3.23.2版本支持Linux内核版本2.6.18到3.18.1。

提取压缩包并编译:

$ tar -xvf ixgbe-3.23.2.tar.gz
$ cd ixgbe-3.23.2/src
$ make 

如果成功,可以在当前目录找到编译完成的驱动(ixgbe.ko)。

可以运行这个命令来查看编译信息:

$ modinfo ./ixgbe.ko 

将会输出一个Ixgbe驱动的可用参数列表

第三步: 加载 Ixgbe 驱动

这步准备加载已经编译好的驱动。

如果系统已经加载了Ixgbe驱动,首先需要卸载掉老版本。否则,新版本不能加载。

$ sudo rmmod ixgbe.ko

然后插入编译完成的驱动到内核中:

$ sudo insmod ./ixgbe.ko

同时,你可以设置启动参数

$ sudo insmod ./ixgbe.ko FdirPballoc=3 RSS=16

验证驱动是否加载成功,使用dmesg命令,查看其输出

$ dmesg 

Intel(R) 10 Gigabit PCI Express Network Driver - version 3.23.2
Copyright (c) 1999-2014 Intel Corporation.
ixgbe 0000:21:00.0: PCI INT A -> GSI 64 (level, low) -> IRQ 64
ixgbe 0000:21:00.0: setting latency timer to 64
ixgbe: Receive-Side Scaling (RSS) set to 16
ixgbe: Flow Director packet buffer allocation set to 3
ixgbe: 0000:21:00.0: ixgbe_check_options: Flow Director will be allocated 256kB of packet buffer
ixgbe: 0000:21:00.0: ixgbe_check_options: FCoE Offload feature enabled
ixgbe 0000:21:00.0: irq 87 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 88 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 89 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 90 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 91 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 92 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 93 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 94 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 95 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 96 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 97 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 98 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 99 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 100 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 101 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 102 for MSI/MSI-X
ixgbe 0000:21:00.0: irq 103 for MSI/MSI-X
ixgbe 0000:21:00.0: eth3: DCA registration failed: -1
ixgbe 0000:21:00.0: PCI Express bandwidth of 32GT/s available
ixgbe 0000:21:00.0: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)
ixgbe 0000:21:00.0: eth3: MAC: 2, PHY: 9, SFP+: 3, PBA No: E68793-006
ixgbe 0000:21:00.0: 90:e2:ba:5b:e9:1c
ixgbe 0000:21:00.0: eth3: Enabled Features: RxQ: 16 TxQ: 16 FdirHash RSC 
ixgbe 0000:21:00.0: eth3: Intel(R) 10 Gigabit Network Connection
ixgbe 0000:21:00.1: PCI INT B -> GSI 68 (level, low) -> IRQ 68
ixgbe 0000:21:00.1: setting latency timer to 64
ixgbe: 0000:21:00.1: ixgbe_check_options: FCoE Offload feature enabled
ixgbe 0000:21:00.0: registered PHC device on eth3
ixgbe 0000:21:00.1: irq 104 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 105 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 106 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 107 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 108 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 109 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 110 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 111 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 112 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 113 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 114 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 115 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 116 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 117 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 118 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 119 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 120 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 121 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 122 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 123 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 124 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 125 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 126 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 127 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 128 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 129 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 130 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 131 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 132 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 133 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 134 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 135 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 136 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 137 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 138 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 139 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 140 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 141 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 142 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 143 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 144 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 145 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 146 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 147 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 148 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 149 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 150 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 151 for MSI/MSI-X
ixgbe 0000:21:00.1: irq 152 for MSI/MSI-X
ADDRCONF(NETDEV_UP): eth3: link is not ready
8021q: adding VLAN 0 to HW filter on device eth3
ixgbe 0000:21:00.1: eth4: DCA registration failed: -1
ixgbe 0000:21:00.1: PCI Express bandwidth of 32GT/s available
ixgbe 0000:21:00.1: (Speed:5.0GT/s, Width: x8, Encoding Loss:20%)
ixgbe 0000:21:00.1: eth4: MAC: 2, PHY: 9, SFP+: 4, PBA No: E68793-006
ixgbe 0000:21:00.1: 90:e2:ba:5b:e9:1e
ixgbe 0000:21:00.1: eth4: Enabled Features: RxQ: 48 TxQ: 48 FdirHash RSC 
ixgbe 0000:21:00.1: eth4: Intel(R) 10 Gigabit Network Connection
ixgbe 0000:21:00.0: eth3: detected SFP+: 3
ixgbe 0000:21:00.1: registered PHC device on eth4
ADDRCONF(NETDEV_UP): eth4: link is not ready
8021q: adding VLAN 0 to HW filter on device eth4
ixgbe 0000:21:00.1: eth4: detected SFP+: 4
ixgbe 0000:21:00.0: eth3: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
ixgbe 0000:21:00.1: eth4: NIC Link is Up 10 Gbps, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
eth3: no IPv6 routers present
eth4: no IPv6 routers present

第四步: 安装Ixgbe驱动

当确认驱动已经加载后,就可以安装驱动到系统中了

$ sudo make install

ixgbe.ko将会安装在下列目录

/lib/modules/<kernel-version>/kernel/drivers/net/ixgbe

此时,编译好的驱动将在启动时自动加载,也可以通过运行命令加载它:

$ sudo modprobe ixgbe 


via: http://ask.xmodulo.com/compile-ixgbe-driver-centos-rhel-fedora.html

作者:Dan Nanni 译者:Vic020 校对:wxy

本文由 LCTT 原创翻译,Linux中国 荣誉推出



最新评论

LCTT 译者
Vic___ 🌟🌟🌟
共计翻译: 39.0 篇 | 共计贡献: 1388
贡献时间:2013-10-13 -> 2017-07-31
访问我的 LCTT 主页 | 在 GitHub 上关注我


返回顶部

分享到微信

打开微信,点击顶部的“╋”,
使用“扫一扫”将网页分享至微信。